Plumbing Basics: The First Step for When Installing a Bathtub
Plumbing Basics: The First Step for When Installing a Bathtub
Blog Article
What're your concepts on How to Install a Bathtub?
Mounting a tub isn't exactly rocket science, yet it does require strong plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a new one is also a moderately tough task. If the old tub is conveniently obtainable, the project can relocate easily; if you have to open up a wall surface to eliminate the old tub and also position the new tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task as well as fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider employing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This short article will aid you install a brand-new bath tub in your shower room if you have currently gotten a brand-new bathtub and also do not require to change the arrangement of your previous water system pipelines.
Your devices as well as product list ought to consist of the following:
Getting ready for the Installment
To start with, the sustaining framework provided with the bathroom must be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome due to the limited access that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, position the tub in the required placement. The wood boards are useful in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bath tub till the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Switch on the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if required. Load the bath tub and likewise check the overflow outlet and the typical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub should wait up until the bathtub has actually been utilized at least when as this will resolve it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washers remain in place between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind should be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack an inflexible seal, triggering the water to penetrate the wall in between the bath and also the tiling, leading to complications with moisture and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealer can fracture relatively very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads on How to Install a Bathtub Yourself, I thought sharing that article post was valuable. Sharing is caring. You never know, you will be doing someone a favor. I praise you for your time. Kindly stop by our website back soon.
Act now! Save later. Report this page